Download
Download

Laden Sie Handbücher, Datenblätter, Software und vieles mehr herunter:

DOWNLOADTYP
MODELL ODER SCHLÜSSELWORT

MSO (Mixed-Signal-Oszilloskop) der Serie 6

Fehlerbehebung und Validierung von Highspeed-Designs heute und in der Zukunft – mit aufrüstbaren Bandbreiten, die bei 1 GHz beginnen und bis zu 8 GHz erweitert werden können. Genaue Messungen mit geringem Rauschen und einer Abtastrate von 25 GS/s, die beim Einschalten der Kanäle nicht absinkt. 

Bandbreite

Bis zu 8 GHz

Abtastrate

25 GS/s pro Kanal

Aufzeichnungslänge

Bis zu 250 Mio. Punkte

Vertikale Auflösung

12 Bit

Geringstes Rauschen bei hoher Empfindlichkeit

>75 % Verringerung des Rauschens bei einem typischen Oszilloskop bei 1 mV/Div

Erkennen Sie Signale, die zuvor nicht sichtbar waren.

  • Niedrigstes Eingangsrauschen dank neuer TEK061 Front-End-ASICs.
  • 12-Bit-Auflösung bei 4 GHz und bis zu 16-Bit-Auflösung bei 200 MHz
Miniaturansicht Entdecken Sie die Technologie hinter dem geringen Rauschen

Erweiterte Messungen und Analyse leicht gemacht

Serie 6 – Konfiguration der Jitteranalyse
Serie 6 – Leistungsqualität
Serie 6 – Serielle Hochgeschwindigkeit
Serie 6 – Viel Kanäle

Charakterisieren Sie Jitter bei GHz-Takten und seriellen Bussen mühelos. Bringen Sie Statistiken ganz unkompliziert in alltägliche Messmittel – mit erweiterten Messungen. Sie können zum Beispiel dieselbe Drag-and-Drop-Aktion für Jitter oder erweiterte Leistungsanalysen als routinemäßige Messungen für Anstiegszeit und Effektivwert verwenden.

  • Erweiterte Jitteranalyse
  • Erweiterte Leistungsanalyse
  • Leistungsschienenmessungen
  • Speicheranalyse und Fehlerbereinigung
  • Konformität für serielle Highspeed-Busse
  • Automatisierte Messungen und Trendanalyse
  • Spektrumansicht Frequenzbereichsanzeige

Signalgüte fängt bei den Tastköpfen an

6-signal-fidelity-rev1.png

Entdecken Sie die Vielseitigkeit mit vier FlexChannel®-Eingängen. Durchsuchen Sie Ihre Schaltkreise mit im Lieferumfang enthaltenen 1 GHZ-10-fach-Tastköpfen. Schließen Sie Hochleistungstastköpfe an – asymmetrische aktive Tastköpfe oder Differenztastköpfe oder beides mit den neuen TriMode-Tastköpfen. Erweitern Sie Ihre Ansicht, indem Sie einen TLP058-Tastkopf an einen beliebigen Eingang anschließen, und erhalten Sie 8 digitale Kanäle – bis zu 32 digitale Kanäle.

  • 1-MΩ- und 50-Ω-Eingangsabschlüsse
  • Vier 1-GHz-Passivtastköpfe mit niedriger Last enthalten
  • Neue TDP7700-Serie TriMode-Tastköpfe mit 4, 6 und 8 GHz
  • Neue TAP4000 und TDP4000 mit 4 GHz und einem oder verschiedenen Tastköpfen

FlexChannel-Eingang

1 hochauflösender analoger Eingang

8 digitale logische Eingänge pro Kanal

Ein Touchscreen, der wirklich funktioniert

  • 15,6-Zoll-Touchscreen, besonders reaktionsschnell
  • Unterstützung von Zweifingergesten
  • Bedienung mit Tasten und Maus

Vertrauen in Zahlen

Eingangskanäle
4 FlexChannel-Eingänge.
Jeder FlexChannel verfügt über 1 analogen Signaleingang oder 8 digitale Logikeingänge mit dem TLP058 Tastkopf

Bandbreite 1
1, 2.5, 4, 6 oder 8 GHz

Abtastrate
25 GS/s auf allen analogen/digitalen Kanälen

Aufzeichnungslänge 1
Bis zu 250 Mio. Punkte auf allen analogen/digitalen Kanälen

Signalgenerator 1
Arbiträr, Sinus, Rechteck, Impuls, Rampe, Dreieck, DC-Pegel, Gauß, Lorentz, Exponentieller Anstieg und Abfall, Sinus(x)/x, Weißes Rauschen, Haversinus, Kardial

Digitalvoltmeter 2
4-stellig

Triggerfrequenzzähler 2
8-stellig

Display
15,6 Zoll (385 mm)
TFT-Farb-HD-Touchscreen (Multitouch) mit einer Auflösung von 1920 x 1080

1 - Optional und upgradefähig
2 - Kostenlos bei Produktregistrierung

Fügen Sie Funktionen und Leistung hinzu, wenn sich Ihre Anforderungen ändern

  • Bandbreite bis 8 GHz hinzufügen
  • Aufzeichnungslänge auf bis zu 250 Mio. Punkte auf jedem Kanal erhöhe
  • Logiktastköpfe für bis zu 32 digitale Kanäle hinzufügen
  • Betriebssystem Windows 10 hinzufügen
  • Arbiträr-Funktionsgenerator hinzufügen
  • Hinzufügen einer erweiterten Analyse: serielle Dekodierung/Triggerung, Leistung, Jitter
    , Speicheranalyse und Fehlerbereinigung sowie automatisierte Konformitätstests

Neue Funktionen und Optionen optimieren die besten Oszilloskope

NEUE Optionen

Kostenlose Upgrades für Geräte mit erweiterten Analyseoptionen

  • Instrumente, die mit der Maskentest-Option ausgestattet sind, erhalten die Signalgrenzwerttestfunktion

Kostenloses Upgrade für alle Geräte

  • Mit Beschriftungen/Lesezeichen können Sie bestimmte Punkte auf Wellenformen oder irgendwo auf der Anzeige mit Anmerkungen versehen
  • Die Frequenzachse in der Spektrum-Ansicht kann jetzt logarithmisch sein
  • Phasenrauschdiagramme sind jetzt mit Phasenrauschmessungen verfügbar

Sie haben bereits ein Gerät der Serie 6? Holen Sie sich ihr Update.

Neue Firmware herunterladen

Was ist im Paket enthalten?

  • 4 TPP1000 1 GHz, niederkapazitive passive Tastköpfe
  • 1 Jahr Garantie auf die enthaltenen Tastköpfe
  • 3 Jahre Garantie auf das Instrument
  • Maus, Netzkabel und Frontschutzdeckel mit angefügtem Zubehörbeutel
  • Die gedruckte Installationsanleitung behandelt die Sicherheit und den grundlegenden Betrieb
  • Umfassende integrierte Onlinehilfe
  • Rückverfolgbarkeitszertifikat
Konfiguration und Angebot
Modell Analogbandbreite Abtastrate Aufzeichnungslänge Analoge Kanäle Digitalkanäle Funktionsgeneratorausgang Listenpreis
MSO64

1 GHz – 8 GHz

25 GS/s

62,5 – 250 Mio. Punkte

4

Bis zu 32 (optional)

1 (optional)

US $26,500
Konfiguration und Angebot
Modell Analogbandbreite Abtastrate Aufzeichnungslänge Analoge Kanäle Digitalkanäle Funktionsgeneratorausgang Listenpreis
MSO64

1 GHz – 8 GHz

25 GS/s

62,5 – 250 Mio. Punkte

4

Bis zu 32 (optional)

1 (optional)

US $26,500
Konfiguration und Angebot
  Tektronix
MSO der Serie 6
Tektronix
MSO der Serie 5
Keysight
Serie S
Rohde & Schwarz
RTP-Serie
Rohde & Schwarz
RTO-Serie
LeCroy
WavePro HD
Detaillierter Vergleich -- -- Datenblatt Datenblatt Datenblatt Datenblatt
Bandbreitenbereiche 1 - 8 GHz 350 MHz bis 2 GHz 500 MHz bis 8 GHz 4 - 8 GHz 600 MHz bis 6 GHz 2,5 - 8 GHz
Bandbreite (auf vier Kanälen) 8 GHz 2 GHz 4 GHz 8 GHz 4 GHz 4 GHz
Aufrüstbare Bandbreite Ja Ja Ja Ja Ja Nein
Anzahl analoger Kanäle 4 4, 6 oder 8 4 4 2 oder 4 4
Kanaleingangsimpedanz 50 Ω, 1 MΩ 50 Ω, 1 MΩ 50 Ω, 1 MΩ 50 Ω 50 Ω, 1 MΩ 50 Ω, 1 MΩ
Analoge Abtastrate (auf vier Kanälen) Bis zu 25 GS/s Bis zu 6,25 GS/s Bis zu 10 GS/s Bis zu 20 GS/s Bis zu 20 GS/s Bis zu 10 GS/s
Standardaufzeichnungslänge (auf vier Kanälen) 62,5 Mio. Punkte 62,5 Mio. Punkte 100 Mio. Punkte 50 Mio. Punkte 50 Mio. Punkte 50 Mio. Punkte
Integrierter Arbiträrsignal-/Funktionsgenerator 50 MHz (opt.) 50 MHz (opt.) Keine Keine 100 MHz (opt.) Keine
Digital- / Logikanalysekanäle (MSO) Bis zu 32 (opt.) Bis zu 64 (opt.) 16 (opt.) 16 (opt.) 16 (opt.) 16 (opt.)
Signalerfassungsrate (wfms/s) >500.000 >500.000 >1.100 950.000 >1.000.000 Nicht verfügbar
Effektivwert Rauschen, 1 mV/Div, bei 1 GHz, 4 GHz, 8 GHz 60 µV, 97 µV, 169 µV 254 µV, n. v., n. v. 90 µV, 153 µV, 260 µV n. v., 270 µV, 430 µV 100 µV, 240 µV, NA n. v., 228 µV, 315 µV
ADC-Auflösung 12 Bit 12 Bit 10 Bit 8 Bit 8 Bit 12 Bit
Betriebssystem Integriertes Betriebssystem
Windows 10 (opt.)
Integriertes Betriebssystem
Windows 10 (opt.)
Windows 10 Windows 10 Windows 7 Windows 10
Standard-Tastköpfe 1 GHz, passive
3,9-pF-Last
Bis zu 1 GHz, passive
3,9-pF-Last
500 MHz passive
9,5-pF-Last
Keine 500 MHz passive
10-pF-Last
500 MHz passive
10-pF-Last
Standardgarantie 3 Jahre 3 Jahre 1 Jahr 3 Jahre 3 Jahre 3 Jahre

Analyse von Netzteilen

MSO64-front-application

Mit der automatisierten Leistungsmessung und -analyse können Sie zuverlässige, wiederholbare Messungen von Leistungsqualität, Oberschwingungen, Schaltverlusten und mehr durchführen. Sparen Sie Zeit mit SPMI-Decodierung und -Triggerung. Und verlassen Sie sich auf die Leistung des MSO der Serie 6 mit geringem Rauschen für die genaue Evaluierung von Netzteilrauschen.

Highlights

  • Spannungsqualität und Oberschwingungen
  • Sicherer Betriebsbereich und Schaltverluste
  • Schaltungsinterne Spulen- und Transformatoranalyse
  • SPMI-Energieverwaltung, Bus-Decodierung und -Triggerung

Jitteranalyse

Serie 6 – Konfiguration der Jitteranalyse

Der Takt ist der Herzschlag jedes eingebetteten Systems und jeder digitalen Kommunikationsschnittstelle. Jitter und andere Taktverzerrungen können den Systembetrieb beeinträchtigen. Ohne das richtige Analysewerkzeug ist es schwierig, die Ursache zu ermitteln.

Highlights

  • Standardphasenrauschen, TIE sowie Frequenzdarstellungen und Histogramme
  • Optionale erweiterte Analyse mit Jitterzerlegung und Taktrückgewinnung

Konformitätsprüfungen auf serielle Standards

MSO64-with-monitor

System sind von der schnellen, zuverlässigen Datenübertragung abhängig. Und digitale Highspeed-Standards brauchen strenge Testverfahren, um diese Zuverlässigkeit zu garantieren. Software für die automatisierte Konformitätsprüfung verwaltet den gesamten Testprozess beim MSO der Serie 6 – Aufbau, Durchführung der Messungen, Überprüfung anhand der Standardgrenzwerte und Erstellung ausführlicher Berichte.

Highlights

  • Ethernet 10/100/1000BASE-T
  • Ethernet XGBT Konformität
  • Ethernet NBASE-T Konformität
  • USB 2.0
  • MIPI D-PHY 1.2
  • Automotive Ethernet 100/1000BASE-T1

Leistungsintegrität

Serie 6 – Leistungsintegrität

Die Platinen von heute können über 20 oder mehr Stromschienen verfügen. Die meisten davon haben weniger als ein paar Volt mit strengen Geräuschgrenzwerten. Genaue Messungen erfordern besondere Aufmerksamkeit.

Highlights

  • Die Option zum digitalen Leistungsmanagement automatisiert Welligkeits- und Ein-/Ausschaltmessungen
  • Kompatibel mit geräuscharmen Power-Rail-Tastköpfe der TPR-Serie
  • Geringes Rauschen des Messsystems
Datenblatt Softwarepaket / Softwareoption Beschreibung Konfiguration und Angebot

Digitale Kanäle einrichten

Upgrade Beschreibung Angebotsdetails
Logiktastkopf TLP058 Jeder Tastkopf nutzt 8 digitale Kanäle auf jedem beliebigen FlexChannel-Eingang Angebot zu diesem Tastkopf anfordern

Gerätefunktionen hinzufügen

Upgrade Beschreibung Angebotsdetails
SUP6-AFG Arbiträr-Funktionsgenerator hinzufügen Testlizenz anfordern

Angebot anfordern
SUP6-DVM Digitalvoltmeter (DVM)/Triggerfrequenzzähler hinzufügen Bei Registrierung wird eine Lizenzdatei für das Software-Upgrade bereitgestellt.
Jetzt registrieren.
SUP6-RL-1 Aufzeichnungslänge auf 125 Mio. Punkte/Kanal erweitern Testlizenz anfordern

Angebot anfordern
SUP6-RL-1T2 Aufzeichnungslänge auf 125 Mio. Punkte/Kanal auf 250 Mio. Punkte/Kanal erweitern Testlizenz anfordern

Angebot anfordern
SUP6-RL-2 Aufzeichnungslänge auf 250 Mio. Punkte/Kanal erweitern Testlizenz anfordern

Angebot anfordern
SUP6-WIN Austauschbares Solid-State-Drive mit installierter Windows 10-Lizenz hinzufügen. Keine Testversion verfügbar

Angebot anfordern

Protokollanalyse hinzufügen

Upgrade Beschreibung Angebotsdetails
SUP6-SR8B10B 8b10b Protokolldekodierung und -suche Testlizenz anfordern

Angebot anfordern
SUP6-SRAERO Serielle Triggerung und Analyse in der Luftfahrt (MIL-STD-1553, ARINC429) Testlizenz anfordern

Angebot anfordern
SUP6-SRAUDIO Serielle Triggerung und Analyse für Audio (I2S, LJ, RJ, TDM) Testlizenz anfordern

Angebot anfordern
SUP6-SRAUTO Serielles Trigger- und Analysemodul für die Fahrzeugtechnik (CAN, CAN FD, LIN, FlexRay) Testlizenz anfordern

Angebot anfordern
SUP6-SRAUTOEN1 100BASE-T1 Protokolldekodierungssoftware für Automotive Ethernet Testlizenz anfordern

Angebot anfordern
SUP6-SRAUTOSEN Serielle Triggerung und Analyse für Automobiltechnik (SENT) Testlizenz anfordern

Angebot anfordern
SUP6-SRCOMP Serielle Triggerung und Analyse für Computertechnik (RS-232/422/485/UART) Testlizenz anfordern

Angebot anfordern
SUP6-SREMBD Serielle Triggering und Analyse für integrierte Systeme (I2C, SPI) Testlizenz anfordern

Angebot anfordern
SUP6-SRENET Serielle Triggerung und Analyse für Ethernet (10Base-T, 100Base-TX) Testlizenz anfordern

Angebot anfordern
SUP6-SRI3C MIPI I3C Dekodierung und Analyse Testlizenz anfordern

Angebot anfordern
SUP6-SRNRZ NRZ Protokolldekodierung und -suche Testlizenz anfordern

Angebot anfordern
SUP6-SRPM Serielles Trigger- und Analysemodul für Energieverwaltung (SPMI) Testlizenz anfordern

Angebot anfordern
SUP6-SRPSI5 PSI5 Serielle Dekodierung und Analyse Testlizenz anfordern

Angebot anfordern
SUP6-SRSPACEWIRE SpaceWire Protokolldekodierung und -analyse Testlizenz anfordern

Angebot anfordern
SUP6-SRUSB2 Serielle Triggerung und Analyse für USB 2.0 (LS, FS, HS) (≥1 GHz-Modell empfohlen für HS) Testlizenz anfordern

Angebot anfordern

Serielle Konformitätsprüfungen hinzufügen

Upgrade Beschreibung Angebotsdetails
SUP6-AUTOEN-BND Automotive Ethernet-Konformität, Signaltrennung, PAM3-Analyse, 100BASE-T1-Dekodierungssoftware Testlizenz anfordern

Angebot anfordern
SUP6-AUTOEN-SS Signaltrennungslösung (min. BW 1 GHz) mit TekExpress Automatisierungsplattform Testlizenz anfordern

Angebot anfordern
SUP6-CMINDUEN10 Automatisierte Konformitätstestlösung für Industrial Ethernet (10Base-T1L mit verlängerter Reichweite) Testlizenz anfordern

Angebot anfordern
SUP6-PAM3 PAM3 automatisierte Konformitätslösung (min. BW 1 GHz) mit TekExpress Automatisierungsplattform Testlizenz anfordern

Angebot anfordern
SUP6-CMAUTOEN Automatisierte Messlösung für Automotive Ethernet (100Base-T1 und 1000BASE-T1) Testlizenz anfordern

Angebot anfordern
SUP6-CMUSB2 Automatisierte Lösung für USB-2.0-Vorab-Konformitätsprüfungen Testlizenz anfordern

Angebot anfordern
SUP6-CMENET Ethernet-Konformitätstestlösung (10/100/1000BASE-T) Testlizenz anfordern

Angebot anfordern
SUP6-CMDPHY MIPI D-PHY 1.2 Konformitätsprüfungslösung Testlizenz anfordern

Angebot anfordern
SUP6-CMNBASET Ethernet (2.5/5GBASE-T) Konformitätstestlösung Testlizenz anfordern

Angebot anfordern
SUP6-CMXGBT Ethernet (10GBASE-T) Konformitätstestlösung Testlizenz anfordern

Angebot anfordern
SUP6-DBLVDS Automatisierte LVDS-Testlösung für MSO-Oszilloskope der Serie 6 Testlizenz anfordern

Angebot anfordern

Erweiterte Analyse hinzufügen

Upgrade Beschreibung Angebotsdetails
SUP6-DPM Vollständige Analyse des digitalen Leistungsmanagement und Fehlerbereinigungslösung (Enthält alle Messungen in DPMBAS + Jitter- und Augendiagrammanalyse) Testlizenz anfordern

Angebot anfordern
SUP6-DJA Erweiterte Jitter- und Augendiagrammanalyse Testlizenz anfordern

Angebot anfordern
SUP6-MTM Masken- und Grenzwertprüfung Testlizenz anfordern

Angebot anfordern
SUP6-PWR Leistungsanalyse Testlizenz anfordern

Angebot anfordern
SUP6-SV-BW-1 Spektrum-Ansicht Erfassungsbreite bis 2 GHz erhöhen Testlizenz anfordern

Angebot anfordern
SUP6-SV-RFVT Spektrumansicht RF zu Zeitanalyse Testlizenz anfordern

Angebot anfordern
SUP6-VID Analoger Videotrigger (NTSC, PAL, SECAM) Testlizenz anfordern

Angebot anfordern

Bandbreiten-Upgrade

Upgrade Beschreibung Angebotsdetails
SUP6-BWxTy4 MSO64-Bandbreiten-Upgrade von x auf y, wobei x und y jeweils Vielfache von MHz sind  

Speicherfehlerbereinigung und Konformität hinzufügen

Upgrade Beschreibung Angebotsdetails
SUP6-DBDDR3 DDR3-Speicher-Fehlerbereinigungslösung Testlizenz anfordern

Angebot anfordern
SUP6-CMDDR3 DDR3/LPDDR3-Konformitätstest Testlizenz anfordern

Angebot anfordern
Zubehör HC5
Datenblatt Beschreibung
Anzeige Datenblatt Hartschalenkoffer für MSO der Serie 5
Zubehör RM5
Datenblatt Beschreibung
Anzeige Datenblatt Rackmount-Kit für MSO der Serie 5
Zubehör SUP6-WIN
Datenblatt Beschreibung
Anzeige Datenblatt Removable SSD with Windows license on 6 Series oscilloscopes
Datenblatt Zubehör Beschreibung
HC5 Hartschalenkoffer für MSO der Serie 5
RM5 Rackmount-Kit für MSO der Serie 5
SUP6-WIN Removable SSD with Windows license on 6 Series oscilloscopes
See how Spectrum View provides ease-of-use and the ability to achieve optimal views in both RF and Time domains simultaneously when analyzing the turn on behavior of a spread spectrum clock.  This …
2:32
Automotive Ethernet with PAM3 introduces new test challenges. Tektronix' new, innovative, non-intrusive Signal Separation simplifies Automotive Ethernet testing and set-up, providing advanced …
0h 8m 3s
Watch how easy it can be to setup and analyze waveform behavior using the highly intuitive touch interface. Setting up your measurement and debugging your system has never been easier with the …
1:51
Learn how to annotate test results and methods with “Callouts” for easily documenting important information when sharing data across a team, recreating a measurement at a later date, or delivering …
1:42
Are you seeing ALL the noise from your power rails? Lee Morgan, Technical Marketing Manager in EMEA, demos one of our power integrity setups with a 6 Series MSO, our new Power Rail Probes, and an …
0h 1m 27s
Learn how to quickly capture bursts just by drawing a couple of boxes, and how to apply logic and add more shapes to capture increasingly complex waveforms. See how visual triggers work on the 5 …
4m 5s
Learn how 5 and 6 Series MSO Mixed-Signal Oscilloscopes and the optional embedded serial bus analysis software provide unparalleled system visibility by decoding MIL-STD 1553 messages, triggering …
0h 3m 14s
An AWG70002B was used to create a pair of 20us wide RF pulse trains at 3.85GHz. One pulse train has a constant/unchanging phase – this is our reference and is applied to Ch1. The other pulse …
3m 29s
See the ultra-low noise performance of the TPR4000 Power Rail Probe, and how it can be used for measuring DC power rail noise in microvolts, especially when paired with the 6 Series MSO …
0h 6m 15s
Learn how to get optimal results from your power supply design by checking the power supply rejection ratio. This video covers how DC-DC  converters or low voltage drop-out regulators (LDOs) …
0h 8m 55s
Test automation may be used to check automotive Ethernet transmitters for compliance with the BroadR-Reach, 100BASE-T1 (P802.3bw), and 1000BASE-T1 (802.3bp) standards. This demonstration shows the …
0h 4m 52s
Make extremely accurate power rail measurements using two Tektronix power rail probes, a Keithley DMM6500 touchscreen Digital Multimeter, and ultra-low-noise 6 Series mixed signal oscilloscope …
0h 1m 46s
Learn how to use the eScope function to remotely control a Tektronix oscilloscope over a network without any special software. This video shows how to find the IP address of the scope and use a …
2:14
How independent time and frequency controls beat traditional FFTs.
0h 6m 19s
What's the big deal with low noise? We talked to our engineers about how they achieved ground-breaking noise performance in the 6 Series Mixed Signal Oscilloscope.
0h 6m 58s
If you're doing mixed frequency/time domain work, Spectrum View makes it easy. Learn how to set up 5 and 6 Series MSOs to display synchronized time and frequency domain views on multiple channels …
0h 6m 0s
Automated Compliance Testing of MIPI D-PHY Physical Layer
The MIPI Alliance has defined tests to ensure that MIPI D-PHY transmitter designs conform to MIPI standards.  D-PHY compliance testing is usually performed using an oscilloscope and may be automated to speed up testing, reduce errors and simplify …

Literaturnummer 48W-61638-0
Anwendungshinweis
Measuring Digital Clock Stability and Jitter with an Oscilloscope
This application note explains how to use oscilloscope measurements to quantify the performance of any digital clock, including processor clocks and communications clocks. It briefly covers amplitude measurements and focuses on clock frequency …

Literaturnummer 48W-61379-1
Anwendungshinweis
What is the range of the logic threshold supported on the 5 and 6 Series MSO?
The logic threshold can be set between +/-40V with the TLP058 logic probe. Each individual digital channel can be set for its own threshold level.
FAQ-ID468126
I recently registered our Tektronix oscilloscope, updated the firmware and am currently trying to activate the free DVM & Frequency Counter.  I don’t see any software downloads for activating the DVM. Am I doing something wrong, or looking in the wrong spot?
After you have registered your oscilloscope on Tek.com, you should have received an email with instructions.  The email is sent to the address you used to login to tek.com.  If you haven't received the email after registration: Check your spam …
FAQ-ID468046
What probe interface does my oscilloscope have?
Oscilloscope series Probe interface CSA7000/CSA7000B TekConnect DPO2000 TekVPI DPO3000 …
FAQ-ID64251
How can I ungroup the channel badge on the 5/6 Series MSO?
On firmware v1.12 or above, the 5/6 Series MSO added the stacked and overlay mode mix and match feature.  It allows user to group multiple channels for overlay mode for easy comparison. To separate the channels in the group, there are couple options …
FAQ-ID773401
I received the following message about my floating license:  (This is a courtesy note to remind you that the checkout of 1 floating license(s) will soon expire.) Why am I receiving this message when I own the license?
The Floating Licenses are good forever; however, the checkout of the Floating License is good for for any duration from 4 hours up to 4 years, selectable at the time of check out.  After it reaches selected duration, it will automatically check …
FAQ-ID467516
How are 5 and 6 Series MSO setup files and session files different? How should I use them?
The 5 and 6 Series MSO setup files contain all instrument settings, user-configured analysis, and reference waveforms, so they provide an easy way to return the oscilloscope to a known state. For example, if you want to build a library of …
FAQ-ID235446
I get an error message “CvP Tester Didn’t Run” on my 5 Series MSO.
Instruments that have both a Linux drive and a Windows drive should have the same firmware revision on both drives. When only one drive has the latest firmware installed, the instrument user may find that firmware is not updated on the Linux drive …
FAQ-ID771991
What user interface differences should I expect to see between a standard 5 or 6 Series MSO and one equipped with the optional Windows 10 operating system?
When you purchase a 5 Series MSO with the 5-WIN option or a 6 Series MSO with the 6-WIN option installed, or upgrade your 5 Series MSO with the SUP5-WIN upgrade, or upgrade your 6 Series MSO with the SUP6-WIN upgrade, you will see very few …
FAQ-ID235441
What is the difference between Windows 10 on my scope and standard Windows 10?
The Windows build on Tektronix scopes is from the Long-Term Servicing Channel (LTSC), specifically Windows 10 Enterprise 2016 LTSB (Long-Term Service Branch 1607).  You can read more about the LTSC here: https://docs.microsoft.com/en-us/windows/whats …
FAQ-ID782291
Where can I find the positive/negative pulse count auto measurement on the 5/6 Series MSO?
Currently, there is no auto measurement for the positive or negative pulse count on the 5/6 Series MSO. The workaround would be using the “Search” feature to search for the pulse width. First, set up for the positive pulse width auto …
FAQ-ID773396
Where can I locate the visual trigger setup on the 5 or 6 series MSO?
The visual trigger option is not listed in the trigger type selection initially.  To setup the visual trigger, simply click on the "DRAW A BOX" icon (located in the lower right corner of the display) to draw the areas for the visual trigger.  After …
FAQ-ID723951
How to extract the trigger time stamp from a Tektronix .wfm file?
The .wfm waveform files saved from Tektronix DPO/DSA/MSO 5K 7K 70K and 5 and 6 Series MSO oscilloscopes contains a time stamp that indicates the time that the scope was triggered. This example program shows how you can extract this time stamp from …
FAQ-ID471231
Can I mount a network drive on my standard (non-Windows) 5 or 6 Series MSO? How could I use this capability?
The oscilloscope has a built-in m.2 drive, labeled C:. This drive can be used to store waveforms, setups, and measurement results. However, this drive is not easily accessible to your computer. The oscilloscope also has several USB ports to support …
FAQ-ID474191
Is e*scope supported on the 5 or 6 series MSO with Windows 10 installed?
Yes.  With firmware v1.8 or above, using the web browser access to the Windows 10 version is supported along with TightVNC.  TightVNC must be installed on both the remote PC and the scope.  For the detailed setup instructions, please see the 5/6 …
FAQ-ID474031
Where are the controls for Roll Mode displays in my 5 and 6 Series MSO?
Roll Mode provides an instant display response when the oscilloscope is operating at very slow sweep speeds. Without it, the acquisition must complete before the display will update. With Horizontal Scale factors as slow as 1000 s/div, that can be a …
FAQ-ID235436
Where do I start learning about oscilloscopes and Tektronix offerings?
This document covers the basics of oscilloscopes including history and general operation, in this training presentation developed by a Tektronix Applications Engineer. Learn the XYZ's of Oscilloscopes »    
FAQ-ID778971
What is the difference between Position and Offset on an oscilloscope?
To answer this first you need to understand the layout of how your waveform trace is displayed. On your oscilloscope you generally will see either 8 or 10 divisions vertically on the screen. Along the left side of the screen you will see a marker …
FAQ-ID247211
How can I invert the channel on the 5 or 6 series MSO?
With firmware v1.16, the invert function is available in the channel menu.  If the unit has the older firmware v1.14 or below, the invert channel feature on the 5 or 6 series MSO is supported via the math channel instead. Here is the setup …
FAQ-ID723956
What is the deskew range and resolution between channels for the 5 or 6 series MSO?
Both 5 and 6 series MSO support a deskew range of -125ns to +125ns. The 6 series MSO can be adjusted in 1ps resolution for all acquisition modes except Peak Detect and Envelope (40ps resolution). The 5 series MSO can be adjusted in 40ps resolution …
FAQ-ID723961
How many digital channels are supported on the 5 and 6 Series MSO?
Each analog channel on the 5 and 6 Series MSO can be converted into 8 digital channels with the logic probe TLP058.  For a 4-channel model (MSO54, MSO64), it is up to 32 digital channels. For a 6-channel model (MSO56), it is up to 48 digital channels …
FAQ-ID468121
How do I set up a network drive on my 5 Series MSO or 6 Series MSO?
Introduction Network drives were introduced in firmware version 1.8.7 for 5 Series, 5 Series Low Profile, and 6 Series MSOs.  This feature allows you to specify a directory on another computer for the scope to use as storage.  To access this storage …
FAQ-ID773296
How do I save and transfer a screenshot from the 4, 5 or 6 Series MSO oscilloscope to my PC via the remote command interface?
Screenshots (also known as hard copies) can be transferred from the Series 4, 5 and 6 MSO oscilloscopes via the remote programming interface using just a few simple commands.  For information on how to send commands to the instrument via the remote …
FAQ-ID245436
How do I keep Windows 10 up to date on my scope?
Updating Windows 10 Using Windows Update By default, Windows 10 will attempt to automatically keep itself up to date with the latest critical security patches, but it will not install optional updates.  To ensure Windows 10 receives all available …
FAQ-ID782296
My Tektronix oscilloscope uses the Linux operating system.  Where do I get a copy of the linux open source code as stated in the GNU Lesser General Public License notice?
For our Linux based instruments or programs licensed under the “GNU General Public License (GPL) or Lesser GNU General Public License (LGPL)” the complete corresponding sources are available. You can order a complete machine-readable copy of the …
FAQ-ID64866
Does my 5 or 6 Series MSO support multiple displays?
Yes, the 5 and 6 Series MSO hardware supports a total of three displays, including the instrument’s internal display. The instrument provides DVI-D, Display Port, and VGA connectors on the rear panel. The standard instrument (running the Linux …
FAQ-ID250721
How do I remotely control my 5 or 6 Series MSO from my computer, easily and without any programming?
For the standard instrument (without the Windows 10 option installed), you can simply connect your computer to the instrument through Ethernet and control the oscilloscope with your favorite browser. Find the instrument’s IP address by selecting …
FAQ-ID474201
I saw a warning message when recalling an instrument setup on my 5 or 6 Series MSO. What caused it?
The 5 and 6 Series MSO will display a pop-up warning message when it is not completely successful recalling the saved state of the instrument with a setup or session file. The following message will appear on the display: WARNING The oscilloscope …
FAQ-ID235416
Does Tektronix have a 12-bit oscilloscope?
Yes! Tektronix offers many different models of real-time oscilloscopes that provide 12-bit or greater vertical resolution for a variety of applications. Because many high-vertical-resolution oscilloscopes on the market have technical trade-offs such …
FAQ-ID69266
I downloaded and Installed OpenChoice Desktop, but it doesn't recognize my scope.
Refer to the Prerequisites.txt file available to download on the same page for OpenChoice desktop. Make sure you have all the prerequisites specified.    Prerequisites 1. PC equipped with  Microsoft Windows 7 32 Bit and 64 Bit OS, Windows 8.1 32 Bit …
FAQ-ID474266
After I place an order for a software-license or an upgrade for my 5 or 6 Series MSO, how do I get and install the software license or the upgrade license?
After you place an order for the software license or an upgrade for your 5 or 6 Series MSO, you will receive an email (at the email address in your MyTek account). It will look about like this, but customized for you: Dear Customer …
FAQ-ID235451
What does “Probe Dynamic Range” mean and how does the 5 and 6 Series MSO indicate it?
Oscilloscope probes which contain active circuitry, especially with amplifiers in the signal path, have a limited dynamic range over which the probe behaves linearly. When input signals exceed this range, the signal may be distorted. (Such probes …
FAQ-ID474196
My scope has Windows 10 version 1607, but more recent versions have been released by Microsoft.  Can my scope be updated?
No, but there is no need to.  The Windows build on Tektronix scopes is from the Long-Term Servicing Channel (Windows 10 Enterprise LTSC). Unlike normal releases of version 1607, this release still receives security updates and support from Microsoft …
FAQ-ID780986
Is it possible to establish a peer to peer ethernet connection on the 5/6 Series MSO?
Yes. To setup a peer to peer connection, you must manually configure the IP and subnet mask address on both the scope and your computer. You can then use an ethernet cable connected directly between the scope and computer.  This will work on the …
FAQ-ID474351
What are some of the advantages of the 5 and 6 Series MSO digital trigger?
Since its invention by Tektronix in the 1940s, the oscilloscope’s trigger system has been a key component of the products, providing a stable display of repetitive signals and the capture of specific events in a signal. At the circuit level, the …
FAQ-ID467411
Decoding and Searching MIPI I3C Bus Activity with an Oscilloscope
The MIPI I3C standard defines a two-wire interface with a bidirectional data bus for connecting sensors to an application processor. This application note gives a brief orientation on the physical layer and packet structures of the I3C protocol. It …

Literaturnummer 48W-61676-0
Anwendungshinweis
EMI Troubleshooting with the Latest-Generation Oscilloscopes
This application note describes techniques using an oscilloscope that can help you determine the source of unwanted radiated emissions (EMI), especially after an out-of-limits condition has been identified through formal testing or pre-compliance …

Literaturnummer 48W-61644-0
Anwendungshinweis
How to Troubleshoot System Problems Using an Oscilloscope with I2C and SPI Decoding
Learn about the physical layers of the most common interchip buses - I2C and SPI - to enable you to troubleshoot bus problems or system issues.  Learn how to set up and interpret the results when you use automated decoding, triggering, and search on …

Literaturnummer 55W-61091-1
Anwendungshinweis
5/6 Series MSO with Option 5-SEC or 6-SEC Enhanced Security
Instrument Declassification and Security Instructions

This document describes how to clear or sanitize 5 Series and 6 Series MSO instruments that have option 5-SEC or 6-SEC installed, to allow removal from a secured area, or returning the instrument for repair.
Teilenummer 077140802
Geheimhaltungsaufhebung
TekExpress Automotive Ethernet (10Base-T1S) Compliance Analysis Solution
TekExpress Automotive Ethernet (10Base-T1S) Compliance Analysis Solution for 5/6 Series Mixed Signal Oscilloscope (MSO)

This document contains operation information for the TekExpress Automotive Ethernet (10Base-T1S) Compliance Analysis Solution. It is a PDF version of the help system accessible in the TekExpress software.
Teilenummer 077167900
Hauptbenutzer
4/5/6 Series MSO
MSO44, MSO46, MSO54, MSO56, MSO58, MSO58LP, MSO64, LPD64 Printable Application Help

This is a printable version of the 4/5/6 Series MSO (MSO44. MSO46, MSO54, MSO56, MSO58, MSO58LP, MSO64, LPD64) on-instrument help system. Supports firmware version 1.22.x.
Teilenummer 077130310
Hauptbenutzer
6 Series MSO
Specifications and Performance Verification

Revision B. For firmware version 1.0 and above. This document contains the specifications and performance verification procedures for the 6 Series MSO instruments.
Teilenummer 077146103
Leistungsprüfung
4, 5, 6 Series MSO (MSO44, MSO46, MSO54, MSO56, MSO58, MSO58LP, MSO64, LPD64)
Programmer Manual

This document describes the remote access programming commands for the MSO44, MSO46, MSO54, MSO56, MSO58, MSO58LP, MSO64, and LPD64 instruments. Supports firmware version 1.22.x.


Teilenummer 077130509
Programmierer
TekExpress Ethernet Compliance Solution for DPO5000/7000/70000 oscilloscopes
TekExpress Ethernet Compliance Solution for DPO5000/7000/70000 oscilloscopes

The application provides more visibility into your Ethernet designs with 1000BASE-T/100BASE-TX/10BASE-T PHY measurements as outlined in IEEE 802.3 Section 40, ANSI X3.263, and IEEE 802.3 Section 14 specific measurements for different Ethernet standards to the already existing rich tool set of generic jitter, timing, and signal quality measurements in Tektronix Oscilloscope.


Teilenummer 077163501
Benutzer
TekExpress Ethernet Compliance Solution
TekExpress Ethernet Compliance Solution

This document contains operation information for the TekExpress Ethernet Tx Compliance Solution. It is a PDF version of the help system accessible in the TekExpress software.


Teilenummer 077150403
Hauptbenutzer
4, 5, 6 Series MSO (MSO44, MSO46, MSO54, MSO56, MSO58, MSO58LP, MSO64, LPD64)
Programmer Manual

This document describes the remote access programming commands for the MSO44, MSO46, MSO54, MSO56, MSO58, MSO58LP, MSO64, and LPD64 instruments. Supports firmware version 1.20.x.


Teilenummer 077130508
Programmierer
4, 5, 6 Series MSO (MSO44, MSO46, MSO54, MSO56, MSO58, MSO58LP, MSO64)
Programmer Manual

Revision A: This document describes the remote access programming commands for the MSO44, MSO46, MSO54, MSO56, MSO58, MSO58LP and MSO64 instruments. Supports firmware version 1.16.x.


Teilenummer 077130507
Programmierer
TekExpress Industrial Ethernet Compliance Solution
TekExpress Industrial Ethernet Compliance Solution

This document contains operation information for the TekExpress Industrial Ethernet Compliance Solution. It is a PDF version of the help system accessible in the TekExpress software.


Teilenummer 077162400
Hauptbenutzer
4/5/6 Series MSO
MSO44, MSO46, MSO54, MSO56, MSO58, MSO58LP, MSO64, LPD64 Printable Application Help

This is a printable version of the 4/5/6 Series MSO (MSO44. MSO46, MSO54, MSO56, MSO58, MSO58LP, MSO64, LPD64) on-instrument help system. Supports firmware version 1.20.x.


Teilenummer 077130308
Hauptbenutzer
TekExpress Automotive PAM3 Analysis Application
TekExpress Automotive PAM3 Analysis Application

Automotive Ethernet operates as a full-duplexcommunication link over a twisted-pair cable. The Full-Duplex communication, along with PAM3 signaling, adds complexity invalidating the Electronic Control Units (ECU) in real-world conditions. The TekExpress Automotive PAM3 Analysis applicationincludes unique Signal Separation capability and Electrical analysis.


Teilenummer 077160600
Benutzer
TekExpress D-PHY Automated Solution for MSO6 oscilloscopes
TekExpress D-PHY Automated Solution for MSO6 oscilloscope Printable Online Help

TekExpress is the Tektronix Test Automation Framework, developed to support your current and future test automation needs. TekExpress uses a highly modular architecture that lets you deploy automated test solutions for various standards in a relativelyshort time.


Teilenummer 077151501
Benutzer
6 Series MSO
Revision B: Specifications and Performance Verification

Revision A: For firmware version 1.0 and above. This document contains the specifications and performance verification procedures for the 6 Series MSO instruments.


Teilenummer 077146102
Leistungsprüfung
4/5/6 Series MSO Option License
Install Instructions

This document describes how to install optional upgrade licenses to add new functions or features to 4/5/6 Series MSO instruments (MSO44, MSO46, MSO54, MSO56, MSO58, MSO58LP, MSO64).


Teilenummer 071351902
Vor-Ort-Installationsanweisungen
5/6 Series MSO (MSO54, MSO56, MSO58, MSO58LP, MSO64)
Programmer Manual

This document describes the remote access programming commands for the MSO54, MSO56, MSO58, MSO58LP and MSO64 instruments. Supports firmware version 1.14.


Teilenummer 077130506
Programmierer
TekExpress Ethernet NBASE-T Compliance Solution
TekExpress Ethernet NBASE-T Compliance Solution

This document contains operation information for the TekExpress Ethernet NBASE-T Compliance Solution. It is a PDF version of the help system accessible in the TekExpress software.


Teilenummer 077152000
Hauptbenutzer
TekExpress D-PHY Automated Solution for MSO6 oscilloscopes
TekExpress D-PHY Automated Solution for MSO6 oscilloscope Printable Online Help

TekExpress is the Tektronix Test Automation Framework, developed to support your current and future test automation needs. TekExpress uses a highly modular architecture that lets you deploy automated test solutions for various standards in a relatively
short time.


Teilenummer 077151500
Benutzer
5/6 Series MSO (MSO54, MSO56, MSO58, MSO58LP, MSO64)
Programmer Manual

This document describes the remote access programming commands for the MSO54, MSO56, MSO58, MSO58LP and MSO64 instruments. Supports firmware version 1.12.


Teilenummer 077130505
Programmierer
Reference Waveform File Format
DPO70000SX, TDS5000, TDS6000/B, TDS7000/B, CSA7000/B, DPO7000/C, DPO70000/B/C/D/DX, DSA70000/B/C/D, MSO70000/C/DX, MSO5000/B, DPO5000/B Series, 5 Series MSO, and 6 Series MSO

This document specifies the reference waveform file format for the instrument.


Teilenummer 077022011
Programmierer
6 Series MSO
MSO64

This manual provides theory of operation, service instructions, and a list of replaceable parts for the 6 Series MSO instruments.


Teilenummer 077146200
Service
6 Series Mixed Signal Oscilloscope
MSO64 Installation and Safety

This manual describes installing and setting up the 6 Series oscilloscope, and introduces the User Interface and basic oscilloscope operations.

Learn the XYZ's of Oscilloscopes »


Teilenummer 071357900
Benutzer
RM5
Rackmount Kit for 5/6 Series MSO

This document supports installing Tektronix 5/6 Series instruments in a rackmount kit to fit in a standard 19-inch equipment rack.


Teilenummer 071352302
Vor-Ort-Installationsanweisungen
5/6 Series MSO With Option 5-SEC Enhanced Security
Instrument Declassification and Security Instructions

This document describes how to clear or sanitize 5 Series MSO instruments (MSO54, MSO56, MSO58) that have option 5-SEC installed, to allow removal from a secured area, or returning the instrument for repair.


Teilenummer 077140801
Geheimhaltungsaufhebung
5/6 Series MSO MSO5, MSO56, MSO58, MSO58LP, MSO64
Install Upgrade Options

This document describes how to install optional upgrade licenses to add new functions or features to 5/6 Series MSO instruments (MSO54, MSO56, MSO58, MSO58LP, MSO64).


Teilenummer 071351901
Vor-Ort-Installationsanweisungen
5/6 Series MSO Option SUP5-WIN, SUP6-WIN
SSD with Microsoft Windows 10 Upgrade Kit

This document describes how to install the Microsoft Windows 10 environment SSD option on the 5/6 Series MSO instruments (MSO54, MSO56, MSO58, MSO64), and how to activate Windows after installation.


Teilenummer 071352401
Vor-Ort-Installationsanweisungen
Read This First
Update your 5/6 Series MSO with the latest firmware

This is a reminder to update your instrument with the latest firmware.


Teilenummer 061442001
Vor-Ort-Installationsanweisungen
TekExpress Automotive Ethernet (10BASE-T1S/100BASE-T1/1000BASE-T1) Automated Compliance Solution - MSO5 and MSO6 series - V1.3.0
Tektronix TekExpress Automotive Ethernet solution provides automated compliance test support for 10BASE-T1S (IEEE Std 802.3cg) standard, 100BASE-T1 (IEEE Std.802.3bw) and 1000BASE-T1 (IEEE Std 802.3bp™-2016) standard for Transmitter electrical test …

Teilenummer 066208900
Anwendungsgebiet
6 Series MSO (Windows OS) Firmware - V1.24.9
Download this firmware to install the latest updates for the 6 Series MSO oscilloscopes. This firmware only applies to oscilloscopes that have option 6-WIN (Windows 10) installed.

Teilenummer 066198606
Firmware
6 Series MSO (non-Windows) Firmware - V1.24.9
Download this firmware to install the latest updates for 6 Series MSO and 6 Series Low Profile Digitizer. This firmware only applies to instruments that do not have option 6-WIN (Windows 10) installed.

Teilenummer 066198506
Firmware
6 Series MSO (Windows OS) Firmware - V1.22.5
Download this firmware to install the latest updates for the 6 Series MSO oscilloscopes. This firmware only applies to oscilloscopes that have option 6-WIN (Windows 10) installed.

Teilenummer 066198604
Firmware
6 Series MSO (non-Windows) Firmware - V1.22.5
Download this firmware to install the latest updates for 6 Series MSO and 6 Series Low Profile Digitizer. This firmware only applies to instruments that do not have option 6-WIN (Windows 10) installed.

Teilenummer 066198504
Firmware
TekExpress Automotive Ethernet (100BASE-T1/1000BASE-T1) Automated Compliance Solution - MSO5 and MSO6 series - V1.2.9
Tektronix TekExpress Automotive Ethernet solution provides automated compliance test support for 100Base-T1 (IEEE Std.802.3bw) and 1000Base-T1 (IEEE Std 802.3bp™-2016) standard for Transmitter electrical test specification as per Open Alliance. The …

Teilenummer 066186014
Anwendungsgebiet
TekExpress Ethernet (1000BASE-T,100BASE-TX and 10BASE-T) Compliance Solution - 5 and 6 Series MSO - V1.2.1
With TekExpress Ethernet Compliance Test Software, engineers validating an Ethernet physical layer can perform reliable compliance tests of 10Base-T, 100Base-TX and 1000Base-T technologies in their labs. This application enhances efficiency with …

Teilenummer 066196755
Anwendungsgebiet
4, 5 and 6 Series MSO, 5 and 6 Series Low Profile Digitizers IVI-COM Driver - V1.6.0
TekSeriesScope IVI-COM Driver for 4, 5 and 6 Series Mixed Signal Oscilloscopes; 5 and 6 Series Low Profile Digitizers IVI Scope class-compliant driver. It complies with Scope Class specifications (IVI-4.1) as defined by the IVI foundation. An IVI …

Teilenummer 066192807
Treiber
Tektronix TekExpress LVDS Automated test solution on the 5/6 Series MSO V1.0.0.
The Tektronix TekExpress LVDS transmitter test application offers a physical layer test solution for transmitter parameter measurements and characterization.

Teilenummer 066170911
Anwendungsgebiet
TEKVISA Connectivity Software - V4.2.0
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol.When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various …

Teilenummer 066093812
Treiber
TekExpress Industrial Ethernet (10BASE-T1L) Automated Compliance Solution - MSO5 and MSO6 series - V1.0.0
TekExpress Industrial Ethernet Compliance Solution - MSO 5000 and 6000The TekExpress Industrial Ethernet application (10Base-T1L) is a compliance test solution for performing transmitter electrical specification measurements and MDI return loss …

Teilenummer 066203600
Anwendungsgebiet
6 Series MSO (non-Windows) Firmware - V1.20.7
Download this firmware to install the latest updates for the 6 series MSO oscilloscopes. This firmware only applies to oscilloscopes that do not have option 6-WIN (Windows 10) installed.

Teilenummer 066198503
Firmware
6 Series MSO (Windows OS) Firmware - V1.20.7
Download this firmware to install the latest updates for the 6 series MSO oscilloscopes. This firmware only applies to oscilloscopes that have option 6-WIN (Windows 10) installed.

Teilenummer 066198603
Firmware
TekExpress Automotive PAM3 Analysis Solution - MSO5 and MSO6 series - V1.0.0
The Tektronix TekExpress Automotive PAM3 Analysis is an automated test solution for performing Signal Separation on a Full duplex 100BASE-T1 Automotive Ethernet signals at system level. User can perform measurements like eye height and eye width can …

Teilenummer 066203300
Anwendungsgebiet
6-CMDPHY - 6 Series MSO - V1.1.0
TekExpress D-PHY Tx software with Option 6-CMDPHY provides unmatched automation for each test with auto-cursor setting or automatic identification of gating areas. This solution supports the D-PHY base specification v1.2 and the D-PHY conformance …

Teilenummer 066170812
Anwendungsgebiet
4, 5 and 6 Series Mixed Signal Oscilloscope IVI-COM Driver - V1.5.0
The TekSeriesScope IVI-COM Driver for 4, 5 and 6 Series Mixed Signal Oscilloscopes is an IVI Scope class-compliant driver. It complies with Scope Class specifications (IVI-4.1) as defined by the IVI foundation. An IVI class-compliant specific driver …

Teilenummer 066192806
Treiber
6 Series MSO (Windows OS) Firmware - V1.16.6
Download this firmware to install the latest updates for the 6 series MSO oscilloscopes. This firmware only applies to oscilloscopes that have option 6-WIN (Windows 10) installed.

Teilenummer 066198602
Firmware
6 Series MSO (non-Windows) Firmware - V1.16.6
Download this firmware to install the latest updates for the 6 series MSO oscilloscopes. This firmware only applies to oscilloscopes that do not have option 6-WIN (Windows 10) installed.

Teilenummer 066198502
Firmware
TekExpress DDR (DDR3 and LPDDR3) - v1.0.0
DDR (Dual Data Rate) is a dominant and fast-growing memory technology. It offers high data transfer rates needed for all computing applications, from the consumer products to the most powerful servers. The high speeds of these signals require a high …

Teilenummer 066196770
Anwendungsgebiet
TekExpress Automotive Ethernet (100BASE-T1/1000BASE-T1) Automated Compliance Solution - MSO5 and MSO6 series - V1.2.8
Tektronix TekExpress Automotive Ethernet solution provides automated compliance test support for 100Base-T1 (IEEE Std.802.3bw) and 1000Base-T1 (IEEE Std 802.3bp?-2016) standard for Transmitter electrical test specification as per Open Alliance. The …

Teilenummer 066186013
Anwendungsgebiet
6 Series MSO (Windows OS) Firmware - V1.14.13
Download this firmware to install the latest updates for the 6 series MSO oscilloscopes. This firmware only applies to oscilloscopes that have option 6-WIN (Windows 10) installed.

Teilenummer 066198601
Firmware
TekExpress Ethernet Nbase-T Automated Compliance Solution - MSO 6 - V1.0.0.70
TekExpress Ethernet NBASE-T Conformance Solution provides turnkey testing & characterization solution for 10GBASE-T measurements as outlined in IEEE 802.3 Section 55, and for 5GBASE-T and 2.5GBASE-T as outlined in IEEE P802.3bz, Section 16; NBASE-T …

Teilenummer 066200100
Anwendungsgebiet
TekExpress Automotive Ethernet (100BASE-T1/1000BASE-T1) Automated Compliance Solution - MSO5 and MSO6 series - V1.2.5
The Tektronix TekExpress Automotive Ethernet solution provides automated compliance test support for 100Base-T1 (IEEE Std.802.3bw) and 1000Base-T1 (IEEE Std 802.3bp™-2016) standard for Transmitter electrical test specification as per Open Alliance …

Teilenummer 066186012
Anwendungsgebiet
5-CMUSB2, 6-CMUSB2 - 5 Series MSO, 6 Series MSO - V1.2.3
The Tektronix USB2.0 compliance test application (Opt. 5-CMUSB2, Opt. 6-CMUSB2) running on a 5 Series MSO and 6 Series MSO oscilloscope provides a one-button compliance testing for USB2.0 devices, hosts, and hubs. The USB software automates the …

Teilenummer 066166808
Anwendungsgebiet
Achieve Higher Vertical Resolution for More Precise Measurements
This white paper describes an approach in which new oscilloscope ADC technology, combined with digital signal processing and a low-noise front end; can provide even higher resolution than found in conventional high bit-rate ADC implementations.  
White Paper
Characterizing and Troubleshooting Jitter with Your Oscilloscope
Gives examples of jitter analysis, from basic analysis using frequency and Time Interval Error (TIE) measurements, to more advanced jitter decomposition techniques to help isolate the sources of jitter.  Shows examples of jitter measurements using …

Literaturnummer 55Z-61099-1
Anwendungshinweis
6 Series MSO Upgrade Guide
Most of the features of the 6 Series MSO are field-upgradable, including bandwidth, record length, arbitrary/function generator, logic channels, and protocol support. This 2-page fact sheet lists all available post-purchase upgrades.

Literaturnummer 48W-61429-5
Datenblatt
In-circuit Measurement of Inductors and Transformers with an Oscilloscope
An oscilloscope can be used to measure the performance of inductors and transformers under operating conditions.  This application note: Provides a quick review of practical inductor and transformer theory, especially related to power supply …

Literaturnummer 55W-61401-2
Anwendungshinweis
Visual Triggers: Graphical Methods for Capturing Bursts and Other Complex Signals on Oscilloscopes
Visual triggers allow you to build triggers by thinking in terms of wave shapes. This technical brief starts by explaining how to quickly capture bursts of specific length by drawing boxes on an oscilloscope display. It then describes how to apply …

Literaturnummer 48W-61452-0
Technisches Informationsblatt
Using FastFrame Segmented Memory on the 4/5/6 Series MSO
Communications systems, RADAR, and ultrasonic sensors all rely on signals that transfer information in bursts followed by dead time. Processor interrupt pulses can occur intermittently and infrequently. Conventional signal-shot acquisitions on …

Literaturnummer 55W-61299-2
Technisches Informationsblatt
Automotive Ethernet: See the True Signal
As the move toward Automotive Ethernet technology in vehicles accelerates, comprehensive design validation is vital to ensure interoperability and reliable operation across multiple ECUs. This application note provides information on Automotive …

Literaturnummer 48W-61604-0
Anwendungshinweis
Power Supply Measurement and Analysis with 4/5/6-PWR Application Software
Optimizing and validating a bench power supply design requires a number of important measurements.  These include: Line-side power quality measurements, such as power factor, inrush current, and harmonics Switching device measurements, such as …

Literaturnummer 55W-61294-3
Anwendungshinweis
Physical Layer Compliance Testing for 1000BASE-T Ethernet
Ethernet compliance testing requires precise test setups and evaluation against limits dictated by IEEE 802.3 standards.  Automated testing software for oscilloscopes greatly simplifies and speeds testing.  This application note summarizes key tests …

Literaturnummer 48W-61620-0
Anwendungshinweis
Troubleshooting USB 2.0 Problems with Your Oscilloscope
Learn the basics of the USB 2.0 physical layer to help you troubleshoot bus problems or system issues.  Learn how to set up and interpret the results when using automated decoding, triggering, and search on an oscilloscope equipped with USB 2.0 bus …

Literaturnummer 55W-61092-1
Anwendungshinweis
Making Accurate Current Measurements on Power Supplies with Oscilloscopes
Accurately measuring current with oscilloscopes is essential for power supply design and general electronics. Learn how to measure current using shunt resistors and voltage probes, and how to use clamp-on current probes with your oscilloscope. Get …

Literaturnummer 51W-60171-2
Anwendungshinweis
LeCroy WavePro HD Series vs. 6 Series MSO Mixed Signal Oscilloscope Comparison
This fact sheet compares important specifications and features of the Tektronix 6 Series MSO Mixed Signal Oscilloscope to those of the LeCroy WavePro HD Series.

Literaturnummer 48W-61427-0
Wettbewerb
Making Higher Accuracy Oscilloscope Measurements
12-bit analog-to-digital converters deliver higher resolution on the 4, 5 and 6 Series MSO oscilloscopes Higher resolution oscilloscope measurements are becoming more important given today’s signal levels. Scopes are available with 12-bit analog-to …
Technisches Informationsblatt
Getting Started with Power Rail Measurements Application Note
No matter the industry, power integrity requirements are becoming more and more strict and the number of critical power rails in a single design is only growing. Traditional power integrity applications typically use passive probes with AC coupling …

Literaturnummer 51W-61562-0
Anwendungshinweis
Ensuring the Performance and Conformance of In-Vehicle Networks for New-Generation Automobiles
Automotive Primer: In-Vehicle Networking This primer provides an overview of the trends, challenges and solutions associated with the expected future evolution of in-vehicle networks, as well as a foundation for testing in-vehicle networks to …

Literaturnummer 48W-61611-0
Einführungshandbuch
Control Loop Analysis Kit for Power Design Stability Measurements
This document describes how the Tektronix Control Loop Analysis Kit provides a simple test setup for validating and debugging feedback loop stability.  This setup also enables engineers to test power supply rejection ratio (PSRR) on the regulator …

Literaturnummer 55W-61596-0
Anwendungsübersicht
Next-Generation Oscilloscopes Brochure - 3 Series MDO, 4 Series MSO, 5 Series MSO, 6 Series MSO
The 3 Series MDO and 4, 5 and 6 Series MSOs offer the largest displays and the greatest user experience of any oscilloscope.  This brochure gives an overview of the platforms, with the similarities and differences between the four series.

Literaturnummer 48W-61573-0
Broschüre
Oscilloscope Selection Guide
From basic signal-checking to high-performance analysis, this selection guide gives an overview of the complete range of oscilloscopes from Tektronix. Comparison tables give high-level specifications and features, and indicate the major differences …

Literaturnummer 46W-31080-7
Auswahlhilfe
Debugging SPMI Power Management Buses with an Oscilloscope
Designers of mobile devices and other portable systems rely on the System Power Management Interface (SPMI) protocol to monitor and dynamically control supply voltages based on real-time system demands. Enabling them to achieve lower power usage at …

Literaturnummer 48W-61436-0
Anwendungshinweis
Debugging SENT Automotive Buses with an Oscilloscope
The SENT bus is used in automotive sensors to transmit high-resolution measurements to electronic control units (ECUs), usually in the powertrain. Decoding the Single Edge Nibble Transmissions (SENT) by looking at the signals can be very difficult …

Literaturnummer 55W-61326-1
Anwendungshinweis
Keysight S-Series vs. 6 Series MSO Mixed Signal Oscilloscope Comparison
This fact sheet compares important specifications and features of the Tektronix 6 Series MSO Mixed Signal Oscilloscope to those of the Keysight S-Series.

Literaturnummer 48W-61424-2
Wettbewerb
Debugging CAN, LIN and FlexRay Automotive Buses with an Oscilloscope
Explains the physical layer basics of common automotive buses - CAN, LIN, and FlexRay - to enable you to troubleshoot bus problems or system issues.  Learn how to set up and interpret the results when using automated decoding, triggering, and search …

Literaturnummer 55W-61098-3
Anwendungshinweis
Troubleshooting Ethernet Problems with your Oscilloscope
Learn the basics of the 10BASE-T and 100BASE-TX Ethernet physical layers to help you troubleshoot bus problems or related system issues. Learn how to set up and interpret the results when using automated decoding, triggering, and search on an …

Literaturnummer 55W-61093-1
Anwendungshinweis
Rohde & Schwarz RTP Series vs. 6 Series MSO Mixed Signal Oscilloscope Comparison
This fact sheet compares important specifications and features of the Tektronix 6 Series MSO Mixed Signal Oscilloscope to those of the Rohde & Schwarz RTP Series.

Literaturnummer 48W-61426-1
Wettbewerb
Rohde & Schwarz RTO2000 Series vs. 6 Series MSO Mixed Signal Oscilloscope Comparison
This fact sheet compares important specifications and features of the Tektronix 6 Series MSO Mixed Signal Oscilloscope to those of the Rohde & Schwarz RTO2000 Series.

Literaturnummer 48W-61425-0
Wettbewerb
Spectrum View: A New Approach to Frequency Domain Analysis on Oscilloscopes
Spectrum View is a new way of performing spectrum analysis on an oscilloscope. This application note shows and explains how Spectrum View operates and how it differs from traditional oscilloscope FFT functions. Any analog signal may be presented as …

Literaturnummer 48W-61563-1
Anwendungshinweis
How can I try out optional features for my 6 Series MSO before I buy them?
Most field upgrades for the optional features for the 6 Series MSO are also available for a one-time, 30-day free trial. These are available simply by requesting a trial software license and installing the node-locked license in the instrument …
FAQ-ID474156
How do I upgrade the bandwidth of my 6 Series MSO and what do I get with the upgrade?
Bandwidth upgrades for the 6 Series MSO can be accomplished by ordering an upgrade product and entering a new software license into the instrument. The instrument bandwidth appears in the Help-> About menu near the top of the window, between the …
FAQ-ID474151
What optional features are available as upgrades for my 6 Series MSO and how do I get the upgrade?
Most optional, factory-installed features for the 6 Series MSO are also available as field upgrades, and are installed simply by ordering an upgrade product and entering a new, node-locked software license into the instrument. There are several …
FAQ-ID474161
Advanced Radar Analysis: Tools for Measuring Modern Radar Application Note
With today's rapid advances in radar technology, developing and manufacturing highly specialized and innovative electronic products to detect radar signals takes leading-edge technology and tools. Tektronix innovative test equipment reduces …

Literaturnummer 37W-23378-4
Anwendungshinweis
Solutions for Aerospace and Defense
For over 70 years Tektronix has offered our military and government partners a range of integrated, clever devices, software, applications and services. Learn more about Tektronix electronic test and measurement solutions designed to address the …

Literaturnummer 46A-61169-2
Broschüre
Probing Techniques for Accurate Voltage Measurements on Power Converters with Oscilloscopes
Making oscilloscope voltage measurements on power supplies is fundamental, but not without challenges. Much is written on oscilloscopes, but probing techniques are often taken for granted. This application note focuses on probing and covers:Choosing …

Literaturnummer 51W-60161-3
Anwendungshinweis
Serial Support Using Tektronix Oscilloscopes and Optional Software
Tektronix oscilloscopes offer a portfolio of optional analysis capabilities to simplify serial bus debug or compliance verification. This selection matrix shows which serial standards are supported by each of the oscilloscope series.

Literaturnummer 55W-29028-13
Auswahlhilfe
Understanding and Performing USB 2.0 Physical Layer Testing
This application note gives an overview of USB 2.0 physical layer testing includingEletrical tests such as signal quality, in-rush current check, drop and droop testsSpecific information on testing high-speed mode complianceTest equipment …

Literaturnummer 55W-61400-0
Anwendungshinweis
Measuring Power Supply Switching Loss with an Oscilloscope
Losses due to dissipation in switching devices such as MOSFET's and IGBT's contribute significantly to the overall losses in switch mode power supplies.  This application note explains how to measure switching loss and conduction loss in power supply …

Literaturnummer 46W-60010-3
Anwendungshinweis